Composite Stapler - Revision history

BradfordBenn at 04:09, 31 August 2022

2022-08-31T04:09:06Z

BradfordBenn at 21:10, 25 August 2022

2022-08-25T21:10:43Z

BradfordBenn at 20:56, 23 August 2022

2022-08-23T20:56:29Z

BradfordBenn at 20:50, 23 August 2022

2022-08-23T20:50:29Z

BradfordBenn: Reformating Table

2022-08-23T20:25:28Z

Reformating Table

BradfordBenn at 20:29, 19 August 2022

2022-08-19T20:29:38Z

BradfordBenn: Start of new page

2022-08-19T19:31:23Z

Start of new page

New page

MakerFX has a composite stapler to secure material in a safer manner. Composite staples reduce the risk for damage to bits, projects, and more importantly humans. It does not completely remove all risk.

{| class="wikitable" style="margin:auto"
|
|
|-
| The composite stapler is located in the cabinet to the left of the miter saw station. || [[File:Cabinet with Stapler.jpg|frameless|200px]]
|-
| It is stored in its original box, please keep the box in good condition until we replace it. || [[File:Composite Stapler Box.jpg|frameless|200px]]
|-
| The composite staples are also stored in the same box. The stapler and the staples are used together. Do not mix and match items, it is a matched pair designed to work together. || [[File:Composite Stapler.jpg|frameless|200px]]
|-
| The staples are loaded from the rear of the stapler. Pull the slide on the side of the stapler back until it locks into place. Then load the staples through the slot in the rear and release the slide. || [[File:Staple Loading Slot.jpg|frameless|200px]]
|-
| Once a week, a few drops of pneumatic oil needs to be dripped into the [fitting on the rear of the stapler. Check the sheet to see the last time it was done, if it was more than seven days ago please drip in two drops and update the log.] ||
|-
| Connect the stapler to the air system. There is an outlet and pressure control on the wall next to the CNC machine. Remember '''you have loaded and powered something that shoots projectiles at high speed'''. Consider it loaded and dangerous at all times. || [[File:Air Drop by CNC.jpg|frameless|200px]]
|-
| Typlically 70PSI (pounds per square inch) will be the proper amount to seat the staple correctly. Do not adjust the pressure until after you have made a test staple. 70PSI seems to work well with multiple materials including hardwoods. You adjust the level with the black knob on the top of the gauge.|| [[File:Pressure control.jpg|frameless|200px]]
|}

← Older revision		Revision as of 04:09, 31 August 2022
Line 63:		Line 63:

	\|}		\|}
		+
		+	[[Category:CNC Router]]

@@ Line 5: / Line 5: @@
+|
 '''
-=== Steps ===
+=== Description ===
 '''
+|
@@ Line 55: / Line 55: @@
 |-
-|style="width: 40%;vertical-align:top;"|Placeholder Text about removing material
+|style="width: 40%;vertical-align:top;"|*Remove your material from the spoil board using a hammer, a board, or a pry bar as appropriate. Be careful not to mark your piece or the spoil board by using a rubber mallet or similar item that leaves marks.
 |[[File:SqcRemoveSmallAnimated.gif|frameless]]
 |}

← Older revision		Revision as of 20:56, 23 August 2022
Line 1:		Line 1:
		+	MakerFX has a Composite Stapler. This specialized stapler is only for use with composite nails. The staples are designed to quickly, easily, and safely attach material to the CNC spoil board. This stapler makes the process of securing material much easier. Metal attachment is not to be used as it shorten the light of the spoil board, as well as being an unwelcome item when others are using the CNC system,.. Not every material will be able to be stapled directly. If you are using one of those materials, use a piece of wood to hold the material and then staple the wood down. Another option is to use the bench dog holes.
		+
	{\|class="wikitable"		{\|class="wikitable"

@@ Line 1: / Line 1: @@
-{|class="wikitable" style="width: 85%;"
+{|class="wikitable"
-|Left Column
-|Right Column
 |-
-|style="width: 60%"|The composite stapler is located in the cabinet to the left of the miter saw station.
+|style="width: 40%;vertical-align:top;"|The composite stapler is located in the cabinet to the left of the miter saw station.
 |[[File:Cabinet with Stapler.jpg|frameless|300px]]
 |-
-|style="width: 60%"|It is stored in its original box, please keep the box in good condition until we replace it.
+|style="width: 40%;vertical-align:top;"|It is stored in its original box, please keep the box in good condition until we replace it.
 |[[File:Composite Stapler Box.jpg|frameless|300px]]
 |-
-|style="width: 60%"|The composite staples are also stored in the same box. The stapler and the staples are used together. Do not mix and match items, it is a matched pair designed to work together.
+|style="width: 40%;vertical-align:top;"|The composite staples are also stored in the same box. The stapler and the staples are used together. Do not mix and match items, it is a matched pair designed to work together.
 |[[File:Composite Stapler.jpg|frameless|300px]]
 |-
-|style="width: 60%"|The staples are loaded from the rear of the stapler. Pull the slide on the side of the stapler back until it locks into place. Then load the staples through the slot in the rear and release the slide.
+|style="width: 40%;vertical-align:top;"|The staples are loaded from the rear of the stapler. Pull the slide on the side of the stapler back until it locks into place. Then load the staples through the slot in the rear and release the slide.
 |[[File:Staple Loading Slot.jpg|frameless|300px]]
 |-
-|style="width: 60%"|Once a week, a few drops of pneumatic oil needs to be dripped into the [fitting on the rear of the stapler. Check the sheet to see the last time it was done, if it was more than seven days ago please drip in two drops and update the log.]
+|style="width: 40%;vertical-align:top;"|Once a week, a few drops of pneumatic oil needs to be dripped into the [fitting on the rear of the stapler. Check the sheet to see the last time it was done, if it was more than seven days ago please drip in two drops and update the log.]
 |Picture
 |-
-|style="width: 60%"|Connect the stapler to the air system. There is an outlet and pressure control on the wall next to the CNC machine. Remember you have loaded and powered something that shoots projectiles at high speed. Consider it loaded and dangerous at all times.
+|style="width: 40%;vertical-align:top;"|Connect the stapler to the air system. There is an outlet and pressure control on the wall next to the CNC machine. Remember you have loaded and powered something that shoots projectiles at high speed. Consider it loaded and dangerous at all times.
-|[File:Air Drop by CNC.jpg|frameless|300px]]
+|[[File:Air Drop by CNC.jpg|frameless|300px]]
 |-
-|style="width: 60%"|Typically 70PSI (pounds per square inch) will be the proper amount to seat the staple correctly. Do not adjust the pressure until after you have made a test staple. 70PSI seems to work well with multiple materials including hardwoods. You adjust the level with the black knob on the top of the gauge.
+|style="width: 40%;vertical-align:top;"|Typically 70PSI (pounds per square inch) will be the proper amount to seat the staple correctly. Do not adjust the pressure until after you have made a test staple. 70PSI seems to work well with multiple materials including hardwoods. You adjust the level with the black knob on the top of the gauge.
-|[[File:Pressure control.jpg|frameless|300px]]
+|[[File:Pressure control.jpg|frameless|150px]]
 |-
-|style="width: 60%"|Placeholder Text about using stapler
+|style="width: 40%;vertical-align:top;"|Placeholder Text about using stapler
 |[[File:SqcAttachSmallAnimated.gif|frameless]]
 |-
-|style="width: 60%"|Placeholder Text about removing material
+|style="width: 40%;vertical-align:top;"|Placeholder Text about removing material
 |[[File:SqcRemoveSmallAnimated.gif|frameless]]
 |-
-|style="width: 60%"|Text
+|style="width: 40%;vertical-align:top;"|Text
 |Picture
 |-
-|style="width: 60%"|Text
+|style="width: 40%;vertical-align:top;"|Text
 |Picture
 |}

@@ Line 1: / Line 1: @@
-MakerFX has a composite stapler to secure material in a safer manner. Composite staples reduce the risk for damage to bits, projects, and more importantly humans. It does not completely remove all risk.
+{|class="wikitable" style="width: 85%;"
 |-
-| The composite stapler is located in the cabinet to the left of the miter saw station. || [[File:Cabinet with Stapler.jpg|frameless|200px]]
+|style="width: 60%"|The composite staples are also stored in the same box. The stapler and the staples are used together. Do not mix and match items, it is a matched pair designed to work together.
 |-
-| It is stored in its original box, please keep the box in good condition until we replace it. || [[File:Composite Stapler Box.jpg|frameless|200px]]
+|style="width: 60%"|The staples are loaded from the rear of the stapler. Pull the slide on the side of the stapler back until it locks into place. Then load the staples through the slot in the rear and release the slide.
 |-
-| The composite staples are also stored in the same box. The stapler and the staples are used together. Do not mix and match items, it is a matched pair designed to work together. ||  [[File:Composite Stapler.jpg|frameless|200px]]
+|style="width: 60%"|Once a week, a few drops of pneumatic oil needs to be dripped into the [fitting on the rear of the stapler. Check the sheet to see the last time it was done, if it was more than seven days ago please drip in two drops and update the log.]
 |-
-| The staples are loaded from the rear of the stapler. Pull the slide on the side of the stapler back until it locks into place. Then load the staples through the slot in the rear and release the slide. || [[File:Staple Loading Slot.jpg|frameless|200px]]
+|style="width: 60%"|Connect the stapler to the air system. There is an outlet and pressure control on the wall next to the CNC machine. Remember you have loaded and powered something that shoots projectiles at high speed. Consider it loaded and dangerous at all times.
 |-
-| Once a week, a few drops of pneumatic oil needs to be dripped into the [fitting on the rear of the stapler. Check the sheet to see the last time it was done, if it was more than seven days ago please drip in two drops and update the log.]	||
+|style="width: 60%"|Typically 70PSI (pounds per square inch) will be the proper amount to seat the staple correctly. Do not adjust the pressure until after you have made a test staple. 70PSI seems to work well with multiple materials including hardwoods. You adjust the level with the black knob on the top of the gauge.
 |-
-| Connect the stapler to the air system. There is an outlet and pressure control on the wall next to the CNC machine. Remember '''you have loaded and powered something that shoots projectiles at high speed'''. Consider it loaded and dangerous at all times. || [[File:Air Drop by CNC.jpg|frameless|200px]]
+|style="width: 60%"|Placeholder Text about using stapler
 |-
-| Typically 70PSI (pounds per square inch) will be the proper amount to seat the staple correctly. Do not adjust the pressure until after you have made a test staple. 70PSI seems to work well with multiple materials including hardwoods. You adjust the level with the black knob on the top of the gauge.|| [[File:Pressure control.jpg|frameless|200px]]
+|style="width: 60%"|Placeholder Text about removing material
 |-
-| Placeholder Text about using stapler || [[File:SqcAttachSmallAnimated.gif|frameless]]
+|style="width: 60%"|Text
 |-
-| Placeholder Text about removing material || [[File:SqcRemoveSmallAnimated.gif|frameless]]
+|style="width: 60%"|Text
 |}