Epilog Laser 101 - Revision history

Jeff at 23:15, 21 February 2021

2021-02-21T23:15:06Z

Jeff at 23:12, 21 February 2021

2021-02-21T23:12:36Z

Jeff: /* Final Checks Before Sending To Laser */

2021-02-21T23:07:56Z

‎Final Checks Before Sending To Laser

Jeff at 22:59, 21 February 2021

2021-02-21T22:59:32Z

Jeff at 22:52, 21 February 2021

2021-02-21T22:52:07Z

Jeff at 22:49, 21 February 2021

2021-02-21T22:49:47Z

Jeff: /* Options */

2021-02-21T22:45:07Z

‎Options

Jeff at 22:44, 21 February 2021

2021-02-21T22:44:03Z

Jeff at 22:20, 21 February 2021

2021-02-21T22:20:40Z

Jeff at 22:04, 21 February 2021

2021-02-21T22:04:28Z

← Older revision		Revision as of 23:15, 21 February 2021
Line 124:		Line 124:

	== Send Job to Epilog Laser ==		== Send Job to Epilog Laser ==
−	<span style="color:red">Make sure the Epilog laser is powered on.</span>	+	*<span style="color:red">Make sure the Epilog laser is powered on.</span>
		+	*Click '''Print''' from the Adobe Print Dialog to send the job to the laser
		+	[[File:Laser 101.19 Adobe Print To Laser.png]]

@@ Line 115: / Line 115: @@
 == Final Checks Before Sending To Laser ==
 #Click '''OK''' to close the Epilog Printing Preferences
-#Document and Media size must MATCH. There is a bug in the Epilog print driver that initially causes them to be different.</span>'''
+#'''<span style="color:red">Document and Media size must MATCH.</span>'''
 #Click '''Setup''' and then '''Preferences''' again
 #Piece Size settings should be the same.

@@ Line 115: / Line 115: @@
 == Final Checks Before Sending To Laser ==
 #Click '''OK''' to close the Epilog Printing Preferences
-#xDocument and Media size must MATCH. There is a bug in the Epilog print driver that initially causes them to be different.</span>'''
+#Document and Media size must MATCH. There is a bug in the Epilog print driver that initially causes them to be different.</span>'''
 #Click '''Setup''' and then '''Preferences''' again
 #Piece Size settings should be the same.

@@ Line 8: / Line 8: @@
 # Click the '''Create New''' button
 #:[[File:Laser 101.01 Adobe - Create New 1.png]]
 # On the right under Preset Details, you need to enter the details of the material you'll be using. The image below shows the most important settings:
 #* ITEM 1: Name of your design.  IE: '''Design1'''

@@ Line 116: / Line 116: @@
 == Final Checks Before Sending To Laser ==
 #Click '''OK''' to close the Epilog Printing Preferences
-#'''<span style="color:red">Document and Media size must MATCH. There is a bug in the Epilog print driver that initially causes them to be different.</span>'''
+#xDocument and Media size must MATCH. There is a bug in the Epilog print driver that initially causes them to be different.</span>'''
 #Click '''Setup''' and then '''Preferences''' again
 #Piece Size settings should be the same.
 #Click '''OK'''
 #Make sure the dimensions for Document and Media match
-#:[[File:Laser 101.18 Epilog Print Document and Media Match]]
+#:[[File:Laser 101.18 Epilog Print Document and Media Match.png]]

@@ Line 78: / Line 78: @@
 *The settings shown on the right are the most common settings.
 *<span style="color:red">Never check Auto Focus. Focus must be set manually.</span>
 |[[File:Laser 101.17 Epilog Print Options.png|200px|left]]
 |- style="vertical-align:top;"
 |style="width: 50%"|
 == Job Type ==
 *'''Raster''' is also known as engraving

@@ Line 54: / Line 54: @@
 #The Epilog Printing Preferences dialog will open and you will need to adjust multiple settings before actually "printing" the design to the Epilog laser.
 #:[[File:Laser 101.16 Epilog Printing Preference.png]]
-#Set the Piece Size so '''Horizontal''' is 7.00 and '''Vertical'' is 5.00
+#There are six sections of parameters that you need to review and adjust for your job.
-{| class="wikitable" style="width: 50%;"
+{| class="wikitable" style="width: 75%;"
 |-
+|
@@ Line 74: / Line 69: @@
 |- style="vertical-align:top;"
 |style="width: 50%"|
 Set the resolution for Rastering. '''400 dpi''' is a good starting point.
 |[[File:Laser 101.17 Epilog Print Resolution.png|200px|left]]
@@ Line 79: / Line 75: @@
 |- style="vertical-align:top;"
 |style="width: 50%"|
-Set the job '''Options'''.
+== Options ==
 |[[File:Laser 101.17 Epilog Print Options.png|200px|left]]
 |- style="vertical-align:top;"
 |style="width: 50%"|
-Set the '''Job Type'''.
+== Job Type ==
 |[[File:Laser 101.17 Epilog Print Job Type.png|200px|left]]
 |- style="vertical-align:top;"
 |style="width: 50%"|
-Set the '''Piece Size'''.
+== Piece Size ==
 |[[File:Laser 101.17 Epilog Print Piece Size.png|200px|left]]
 |- style="vertical-align:top;"
 |style="width: 50%"|
-Set the '''Raster Settings'''.
+== Raster Settings ==
-|[[File:Laser 101.17 Epilog Print Raster Setting.png|300px|left]]
+*Refer to this guide to determine Speed and Power for the material being used. This guide is located on a slide out on the left side of the desk.
 |- style="vertical-align:top;"
 |style="width: 50%"|
-Set the '''Vector Settings'''.
+== Vector Settings ==
-|[[File:Laser 101.17 Epilog Print Vector Setting.png|300px|left]]
+This section will be active if the Job Type is Vector or Combined
 |}

← Older revision		Revision as of 22:20, 21 February 2021
Line 59:		Line 59:

	#:[[File:Laser 101.18 Epilog Print Document and Media Match]]		#:[[File:Laser 101.18 Epilog Print Document and Media Match]]
		+
		+
		+	{\| class="wikitable" style="width: 50%;"
		+	\|-
		+	\|
		+	'''
		+	=== Step ===
		+	'''
		+	\|
		+	'''
		+	=== Visual ===
		+	'''
		+
		+	\|- style="vertical-align:top;"
		+	\|style="width: 50%"\|
		+	Set the resolution for Rastering. '''400 dpi''' is a good starting point.
		+	\|[[File:Laser 101.17 Epilog Print Resolution.png\|200px\|left]]
		+
		+	\|- style="vertical-align:top;"
		+	\|style="width: 50%"\|
		+	Set the job '''Options'''.
		+	\|[[File:Laser 101.17 Epilog Print Options.png\|200px\|left]]
		+
		+	\|- style="vertical-align:top;"
		+	\|style="width: 50%"\|
		+	Set the '''Job Type'''.
		+	\|[[File:Laser 101.17 Epilog Print Job Type.png\|200px\|left]]
		+
		+	\|- style="vertical-align:top;"
		+	\|style="width: 50%"\|
		+	Set the '''Piece Size'''.
		+	\|[[File:Laser 101.17 Epilog Print Piece Size.png\|200px\|left]]
		+
		+	\|- style="vertical-align:top;"
		+	\|style="width: 50%"\|
		+	Set the '''Raster Settings'''.
		+	\|[[File:Laser 101.17 Epilog Print Raster Setting.png\|300px\|left]]
		+
		+	\|- style="vertical-align:top;"
		+	\|style="width: 50%"\|
		+	Set the '''Vector Settings'''.
		+	\|[[File:Laser 101.17 Epilog Print Vector Setting.png\|300px\|left]]
		+
		+	\|}

← Older revision		Revision as of 22:04, 21 February 2021
Line 57:		Line 57:
	#Click '''OK'''		#Click '''OK'''
	#:[[File:Laser 101.17 Epilog Print Piece Size 7x5.png]]		#:[[File:Laser 101.17 Epilog Print Piece Size 7x5.png]]
		+
		+	#:[[File:Laser 101.18 Epilog Print Document and Media Match]]