Sawstop 10 inch Professional Cabinet Saw - Revision history

Joe.Gravelle: /* Shutdown Procedures */

2022-07-27T15:56:57Z

‎Shutdown Procedures

2022-04-02T13:51:16Z

made the shutdown / cleanup process more obvious

2019-07-04T00:26:59Z

‎Useful References

2019-05-12T20:37:12Z

2018-03-18T20:23:01Z

‎General Policies for the SawStop PCS

2018-03-18T20:22:36Z

2018-03-18T20:12:39Z

2018-03-18T20:09:27Z

2018-03-18T20:08:20Z

‎Maintenance

2018-03-18T20:06:19Z

← Older revision		Revision as of 15:56, 27 July 2022
Line 33:		Line 33:
	* Unplug from the wall and store the cord away		* Unplug from the wall and store the cord away

		+
		+
		+	* Blade guard is reinstalled if a riving knife was swapped out
		+	* Fence is parked on the black table surface

	=Equipment Features=		=Equipment Features=

@@ Line 24: / Line 24: @@
 *Turn the power switch to on and allow the saw to do its self check. Reference the side of the switch box for the light blink codes. If the saw will not power on, do not force it to work. Message the POC
 *Once the saw is ready the green light will illuminate and the saw is ready for operation
 =Equipment Features=
@@ Line 48: / Line 57: @@
 =Maintenance=
-Regular maintenance of the saw is required and will be carried out by the area contact. But after every use please clean any sawdust from the saw, lower the blade, place any tools back to their homes, and turn the saw off (unplug from the wall and store the cord away)
+Regular maintenance of the saw is required and will be carried out by the area contact.
 Common Setup Tips: For those interested

@@ Line 44: / Line 44: @@
 *The Accurate Tale Saw by Ian J. Kirby [https://www.amazon.com/Accurate-Table-Saw-Cambium-Handbook/dp/0964399954/ref=sr_1_9?ie=UTF8&qid=1521404033&sr=8-9&keywords=table+saw+book]
 *7 Things To Get You Started Using The Table Saw - Wood Working for Mere Mortals [https://www.youtube.com/watch?v=91v0Yg1L4ok]
 =Maintenance=

@@ Line 35: / Line 35: @@
 =Current Collection of Jigs or Special Tools=
-*Crosscut Sled -> to be made
+*Crosscut Sled
-*Jointing Sled -> to be made
+*Jointing Sled
 *Push Stick
 *MicroJig GRR-Ripper push block [https://www.microjig.com/products/grr-ripper]

@@ Line 13: / Line 13: @@
 '''General Disclaimer'''
-SawStop's Flesh Detection technology cannot stop kickback. If you are unsure of what you are about to do, stop and ask for assistance.
+SawStop's Flesh Detection technology cannot prevent kickback or all injuries. If you are unsure of what you are about to do, stop and ask for assistance.
 =Saw Use and Startup Procedures=

@@ Line 9: / Line 9: @@
 No cutting of conductive materials such as aluminum, wet wood, pressure treated, or otherwise known conductive materials. Cutting these types of materials will trigger the blade brake and destroy the blade.
-If you trip the brake on the saw, accidental( flesh to blade contact or the material tripping the brake), please alert the zone POC. You are also responsible for replacing at least the blade if the brake was proven to be tripped by flesh contact, a $50 blade is cheaper than losing a hand. SawStop will replace the brake free of charge if its sent to them after an incident and they find it was tripped by flesh contact.
+If you trip the brake on the saw, accidentally( flesh to blade contact or the material tripping the brake), please alert the zone POC and you'll probably wish you had put on your brown pants. You are also responsible for replacing at least the blade if the brake was proven to be tripped by flesh contact, a $50 blade is cheaper than losing a hand. SawStop will replace the brake free of charge if its sent to them after an incident and they find it was tripped by flesh contact.
 '''General Disclaimer'''
@@ Line 39: / Line 39: @@
 *Push Stick
 *MicroJig GRR-Ripper push block [https://www.microjig.com/products/grr-ripper]
 =Maintenance=

← Older revision		Revision as of 20:12, 18 March 2018
Line 14:		Line 14:

	SawStop's Flesh Detection technology cannot stop kickback. If you are unsure of what you are about to do, stop and ask for assistance.		SawStop's Flesh Detection technology cannot stop kickback. If you are unsure of what you are about to do, stop and ask for assistance.
		+
		+	=Saw Use and Startup Procedures=
		+
		+	After being cleared on the saw but needing a reminder please reference the below list on how to setup to cut on the table saw
		+
		+	*Plug the saw in to power
		+	*Verify the dust collection is hooked up to the saw, it may have been disconnected and put away.
		+	*Ensure the table is clear of any materials and the blade guard is in place
		+	*Turn the power switch to on and allow the saw to do its self check. Reference the side of the switch box for the light blink codes. If the saw will not power on, do not force it to work. Message the POC
		+	*Once the saw is ready the green light will illuminate and the saw is ready for operation

	=Equipment Features=		=Equipment Features=

← Older revision		Revision as of 20:09, 18 March 2018
Line 10:		Line 10:

	If you trip the brake on the saw, accidental( flesh to blade contact or the material tripping the brake), please alert the zone POC. You are also responsible for replacing at least the blade if the brake was proven to be tripped by flesh contact, a $50 blade is cheaper than losing a hand. SawStop will replace the brake free of charge if its sent to them after an incident and they find it was tripped by flesh contact.		If you trip the brake on the saw, accidental( flesh to blade contact or the material tripping the brake), please alert the zone POC. You are also responsible for replacing at least the blade if the brake was proven to be tripped by flesh contact, a $50 blade is cheaper than losing a hand. SawStop will replace the brake free of charge if its sent to them after an incident and they find it was tripped by flesh contact.
		+
		+	'''General Disclaimer'''
		+
		+	SawStop's Flesh Detection technology cannot stop kickback. If you are unsure of what you are about to do, stop and ask for assistance.

	=Equipment Features=		=Equipment Features=

← Older revision		Revision as of 20:08, 18 March 2018
Line 29:		Line 29:

	Regular maintenance of the saw is required and will be carried out by the area contact. But after every use please clean any sawdust from the saw, lower the blade, place any tools back to their homes, and turn the saw off (unplug from the wall and store the cord away)		Regular maintenance of the saw is required and will be carried out by the area contact. But after every use please clean any sawdust from the saw, lower the blade, place any tools back to their homes, and turn the saw off (unplug from the wall and store the cord away)
		+
		+	Common Setup Tips: For those interested
		+
		+	* Checking Blade to Miter Slot Parallelism [https://www.youtube.com/watch?v=jvjZKFSXkNA]
		+	* Fence to Blade / Miter Slot Parallelism [https://www.youtube.com/watch?v=PYq9FWrcIos]

@@ Line 18: / Line 18: @@
 * Overarm Dust Collection
 * Dust Collector Blade Guard
 =Maintenance=
 Regular maintenance of the saw is required and will be carried out by the area contact. But after every use please clean any sawdust from the saw, lower the blade, place any tools back to their homes, and turn the saw off (unplug from the wall and store the cord away)