Difference between revisions of "Sheldon Metal Lathe"
| (One intermediate revision by the same user not shown) | |||
| Line 1: | Line 1: | ||
[[File:Sheldon-Metal-Lathe-TS44E.jpg|400px|thumb|right]] | [[File:Sheldon-Metal-Lathe-TS44E.jpg|400px|thumb|right]] | ||
| + | =Sheldon 11” Tool Room Precision Lathe= | ||
=TS-44 E model= | =TS-44 E model= | ||
| Line 8: | Line 9: | ||
* E - 4 speed under drive with 4 step pulleys (or possibly 8 speeds if the primary pulley has two steps instead of 1. | * E - 4 speed under drive with 4 step pulleys (or possibly 8 speeds if the primary pulley has two steps instead of 1. | ||
| + | =Sheldon “E” Type Underneath Motor Drive= | ||
| − | + | * Double countershaft permits operation through standard 1-piece lathe bed | |
| + | * Double V-belts to spindle prevent slippage and delivers full power | ||
| + | * 4 step cones give wide speed range | ||
| + | * Lever release for belt shifting | ||
| + | * Adjustable take-up for all belts | ||
| + | |||
| + | * Motor - 1 HP (need to confirm) | ||
| + | |||
| + | 8 hand-switched speeds... | ||
* Back gears engaged: 50, 87, 142, 244 | * Back gears engaged: 50, 87, 142, 244 | ||
* Open belt: 280, 482, 788, 1355 | * Open belt: 280, 482, 788, 1355 | ||
| Line 27: | Line 37: | ||
* Large face plate diameter - 11” | * Large face plate diameter - 11” | ||
* Small dog plate diameter - 5 1/2” | * Small dog plate diameter - 5 1/2” | ||
| + | |||
| + | =Tooling= | ||
| + | * 3 Jaw Chuck | ||
| + | * Quick Change Tool Post | ||
| + | * 7 Tool Holders | ||
| + | * Insert Tooling Set (with extra inserts) | ||
| + | * Assorted High Speed Steel Tooling | ||
| + | * Boring Bar | ||
| + | * Threading Dial | ||
| + | * Dead Center | ||
| + | * Live Center | ||
| + | * Drill Chuck | ||
Latest revision as of 16:52, 4 June 2021
Contents
Sheldon 11” Tool Room Precision Lathe
TS-44 E model
- T - Indicated a taper attachment or tapered roller spindle bearings
- S - Later 11” swing (clearance measures at an actual 11-1/4” over the bed and carriage wings), “short” #5MT spindle taper; 2-1/4” x 8 TPI spindle thread
- 44 - Bed length in inches
- E - 4 speed under drive with 4 step pulleys (or possibly 8 speeds if the primary pulley has two steps instead of 1.
Sheldon “E” Type Underneath Motor Drive
- Double countershaft permits operation through standard 1-piece lathe bed
- Double V-belts to spindle prevent slippage and delivers full power
- 4 step cones give wide speed range
- Lever release for belt shifting
- Adjustable take-up for all belts
- Motor - 1 HP (need to confirm)
8 hand-switched speeds...
- Back gears engaged: 50, 87, 142, 244
- Open belt: 280, 482, 788, 1355
Capacity and Clearances
- Swing over bed - 11 1/4
- Swing over cross slide - 8”
- Distance between centers - 35”
- Carriage length - 13”
- Carriage bridge wide - 4 1/2”
- Bed length - 44”
- Bed width - 8”
- Bed height - 6 9/16”
Headstock
- Hole through spindle - 1 3/8”
- Large face plate diameter - 11”
- Small dog plate diameter - 5 1/2”
Tooling
- 3 Jaw Chuck
- Quick Change Tool Post
- 7 Tool Holders
- Insert Tooling Set (with extra inserts)
- Assorted High Speed Steel Tooling
- Boring Bar
- Threading Dial
- Dead Center
- Live Center
- Drill Chuck
