Difference between revisions of "Deltamaker 2"

From MakerFX Wiki!
Jump to: navigation, search
Line 62: Line 62:
 
| 1
 
| 1
 
| [http://things.deltamaker.com/support/DeltaMaker-Getting-Started-Guide.pdf#page=8 Calibration]
 
| [http://things.deltamaker.com/support/DeltaMaker-Getting-Started-Guide.pdf#page=8 Calibration]
 
1. Make sure your DeltaMaker 3D Printer is at temperature (230°C).
 
 
2. Grasp the filament directly below the extruder drive, and pinch the trigger.
 
 
3. PUSH a few centimeters of filament into the extruder, and observe a string of melted filament exiting the nozzle.
 
 
4. Then, SLOWLY PULL the filament out of the extruder, and recoil it on your filament spool.
 
 
 
| [[File:Deltamaker-Calibration.jpg|400px|right]]
 
| [[File:Deltamaker-Calibration.jpg|400px|right]]
 
| Need volunteer!
 
| Need volunteer!
Line 83: Line 74:
 
| 3
 
| 3
 
| [http://things.deltamaker.com/support/DeltaMaker-Getting-Started-Guide.pdf#page=18 Instructions if you need to unload filament]
 
| [http://things.deltamaker.com/support/DeltaMaker-Getting-Started-Guide.pdf#page=18 Instructions if you need to unload filament]
 +
 +
1. Make sure your DeltaMaker 3D Printer is at temperature (230°C).
 +
 +
2. Grasp the filament directly below the extruder drive, and pinch the trigger.
 +
 +
3. PUSH a few centimeters of filament into the extruder, and observe a string of melted filament exiting the nozzle.
 +
 +
4. Then, SLOWLY PULL the filament out of the extruder, and recoil it on your filament spool.
 +
 
|
 
|
 
| Need volunteer!
 
| Need volunteer!

Revision as of 15:59, 31 August 2018

edit 

REMEMBER To Reserve Time!

Various tools such as the lasers (Epilog or Audrey), 3D Printers, and Forest CNC need to be reserved before using the tool. Review the Slack channel for the tool to reserve time.


edit 

NOTICE!

PLA only! No PETG or ABS / Local Source for PLA (Get MakerFX discount code from zone manager)


DeltaMaker Printers at MakerFX

The DeltaMaker printers have OctoPrint built-in which includes a built-in slicer. Click any of the printers below to be directed to OctoPrint.

Login as admin with password of 3dadmin to operate the printer.

deltamaker-0197

deltamaker-0187

deltamaker-0168

Deltamaker.jpg
Deltamaker.jpg
Deltamaker.jpg
http://192.168.1.98 http://192.168.1.204 http://192.168.1.202
240mm hexagon x 260 mm 240mm hexagon x 260 mm 240mm hexagon x 260 mm
Heated Bed = NO Heated Bed = NO Heated Bed = NO
Nozzle = 0.40 Nozzle = 0.40 Nozzle = 0.40


Pre-Flight Instructions

Once these steps are completed, they do not need to be completed before each and every print in a given session. They only take a few minutes to complete and it will ensure you have a good experience with the printer.

Step Text Instructions Screenshot Video Instructions
1 Calibration
Deltamaker-Calibration.jpg
Need volunteer!
2 Setting nozzle height
Deltamaker-SetNozzleHeight.jpg
Need volunteer!
3 Instructions if you need to unload filament

1. Make sure your DeltaMaker 3D Printer is at temperature (230°C).

2. Grasp the filament directly below the extruder drive, and pinch the trigger.

3. PUSH a few centimeters of filament into the extruder, and observe a string of melted filament exiting the nozzle.

4. Then, SLOWLY PULL the filament out of the extruder, and recoil it on your filament spool.

Need volunteer!
4 Loading filament Need volunteer!
5 Preparing to print Need volunteer!


Consumables

  • Tape
  • Sandpaper (80 grit)
  • Purple Disappearing Glue Stick


Information


Maintenance


Go to Main Page

Report Dead Links