Difference between revisions of "Forest CNC Set Job Home"

From MakerFX Wiki!
Jump to: navigation, search
 
(30 intermediate revisions by 2 users not shown)
Line 14: Line 14:
 
'''
 
'''
  
−
|-
+
|- style="vertical-align:top;"
−
|style="width: 50%"|
+
|style="width: 35%"|
 
=== 1. Secure the material ===
 
=== 1. Secure the material ===
−
*Use clamps or whatever method is appropriate for your job
+
*Metal attachment is not to be used as it shorten the light of the spoil board, as well as being an unwelcome item when others are using the CNC system. Not every material canbe stapled directly. If you are using one of those materials, use a piece of wood to hold the material and then staple the wood down. Another option is to use the bench dog holes.
 +
*MakerFX has a [[Composite Stapler]] specifically for securing wood to the CNC spoil board. The use of screws or other metal methods is no longer allowed.
 
*You may have to use '''CNC Controls''' and manually move the gantry to allow room to secure your material
 
*You may have to use '''CNC Controls''' and manually move the gantry to allow room to secure your material
−
|screenshot needed
+
|[[File:Composite Stapler.jpg|300px|left]]
  
−
|-
+
|- style="vertical-align:top;"
 
|
 
|
−
=== 2. Move Gantry To Job Home ===
+
=== 2. Move Gantry To Job Home - Get Close ===
 
*Use '''CNC controls''' to move the gantry to the desired home position
 
*Use '''CNC controls''' to move the gantry to the desired home position
 
*To travel quickly to the other end of the table, enable Rabbit mode by clicking the '''Turtle / Rabbit''' button until the light is '''OFF'''
 
*To travel quickly to the other end of the table, enable Rabbit mode by clicking the '''Turtle / Rabbit''' button until the light is '''OFF'''
 
*Move gantry to approximate home position
 
*Move gantry to approximate home position
 +
|[[File:CNC_Jog_Speed_Fast.png|300px|left]]
 +
 +
|- style="vertical-align:top;"
 +
|
 +
=== 3. Move Gantry To Job Home - Fine Tune ===
 
*Set '''Turtle mode'''
 
*Set '''Turtle mode'''
 
*Fine tune position until you get to the desired home position for X and Y
 
*Fine tune position until you get to the desired home position for X and Y
 
*Setting Z home can be done automatically and discussed below
 
*Setting Z home can be done automatically and discussed below
−
|screenshot needed
+
|[[File:CNC_Jog_Speed_Slow.png|300px|left]]
 +
 
  
−
|-
+
|- style="vertical-align:top;"
 
|
 
|
−
=== 3. Set new Home coordinates ===
+
=== 4. Set new Home coordinates ===
 
*Click '''SETUP (F1)''' -> '''PART Mode (F1)'''
 
*Click '''SETUP (F1)''' -> '''PART Mode (F1)'''
 +
|[[File:CNC_F1_Setup.png|800px|left]]
 +
[[File:CNC_F1_Part.png|400px|left]]
 +
 +
|- style="vertical-align:top;"
 +
|
 +
=== Set X Position ===
 
*Press '''SET (F10)''' to set the X Home value to the current position.
 
*Press '''SET (F10)''' to set the X Home value to the current position.
 
*Click '''NEXT AXIS (F1)''' to advance to Y
 
*Click '''NEXT AXIS (F1)''' to advance to Y
 +
|[[File:CNC_Set_X.png|400px|left]]
 +
 +
|- style="vertical-align:top;"
 +
|
 +
=== Set Y Position ===
 
*Click '''SET (F10)''' to set the Y Home to the current position
 
*Click '''SET (F10)''' to set the Y Home to the current position
 
*Click '''NEXT AXIS (F1)''' to advance to Z
 
*Click '''NEXT AXIS (F1)''' to advance to Z
−
*Using the '''CNC Controls''', move Gantry away from edge to create space for probe using the X,Y & Z move buttons
+
|[[File:CNC_Set_Y.png|400px|left]]
−
*Click the '''AUTO (F4)''' button and CYCLE START
+
 
−
*Test probe by clicking button to assure button click registers
+
|- style="vertical-align:top;"
−
*Put probe in place under the bit
+
|
−
*Click '''CYCLE START''' to initiate auto setting the Z home
+
=== Set Z Position ===
−
*The CNC will move the Z axis to set the new Z Home value
+
*Click '''SET (F10)''' to set the Z Home to the current position
−
*'''DO NOT''' press SET (F10) at this point. The Z value has been automatically set.
+
*Click '''NEXT AXIS (F1)''' to return to X
−
*Using the '''CNC Controls''', press '''Z+''' to move the bit away from the probe
+
|[[File:CNC_Set_Z.png|400px|left]]
−
*Remove probe and place it safely back on top of the controller
 
−
|screenshot needed
 
  
−
|-
+
|- style="vertical-align:top;"
 
|
 
|
−
=== 4. Confirm Job Home ===
+
=== 5. Confirm Job Home ===
 
*Press '''ESCAPE''' a few times to return to the main menu
 
*Press '''ESCAPE''' a few times to return to the main menu
 
*Select '''MDI (F3)'''
 
*Select '''MDI (F3)'''
−
*Enter '''x0y0z0.25''' in the Block and press ENTER to accept the command and then CYCLE START
+
*Enter '''x0y0z0.25''' in the Block and press '''ENTER''' to accept the command and then '''CYCLE START'''
 
*The CNC will move the bit to the job home position with the bit setting at 1/4" above the surface of the material
 
*The CNC will move the bit to the job home position with the bit setting at 1/4" above the surface of the material
 
*You can use '''x0y0z0''' if you want the bit to touch the material
 
*You can use '''x0y0z0''' if you want the bit to touch the material
 
*Using the '''CNC Controls''', press '''Z+''' to move the bit away from the material
 
*Using the '''CNC Controls''', press '''Z+''' to move the bit away from the material
−
|screenshot needed
+
|[[File:CNC_F3_MDI.png|800px|left]]
 +
[[File:CNC_Confirm_Home_A.png|500px|left]]
  
−
|-
+
|- style="vertical-align:top;"
 
|
 
|
 
=== SUCCESS ===
 
=== SUCCESS ===
 
*You have successfully set Job Home
 
*You have successfully set Job Home
 
*Next step is to '''[[Forest_CNC_Run_Job | load and run your job]]'''
 
*Next step is to '''[[Forest_CNC_Run_Job | load and run your job]]'''
 +
|
 +
 +
|- style="vertical-align:top;"
 +
|
 +
=== NEXT STEP ===
 +
 +
[[ Forest_CNC_Run_Job | Click here for the next step ]]
 
|
 
|
  
 
|}
 
|}
 +
 +
[[Category:CNC Router]]

Latest revision as of 20:14, 30 August 2022

edit 

REMEMBER To Reserve Time!

Various tools such as the lasers (Epilog or Audrey), 3D Printers, and Forest CNC need to be reserved before using the tool. Review the Slack channel for the tool to reserve time.


Follow these steps to set the home position for your job. Think about how you have defined the job in VCarve Pro and set the home position to match that design.

Steps

Visual

1. Secure the material

  • Metal attachment is not to be used as it shorten the light of the spoil board, as well as being an unwelcome item when others are using the CNC system. Not every material canbe stapled directly. If you are using one of those materials, use a piece of wood to hold the material and then staple the wood down. Another option is to use the bench dog holes.
  • MakerFX has a Composite Stapler specifically for securing wood to the CNC spoil board. The use of screws or other metal methods is no longer allowed.
  • You may have to use CNC Controls and manually move the gantry to allow room to secure your material
Composite Stapler.jpg

2. Move Gantry To Job Home - Get Close

  • Use CNC controls to move the gantry to the desired home position
  • To travel quickly to the other end of the table, enable Rabbit mode by clicking the Turtle / Rabbit button until the light is OFF
  • Move gantry to approximate home position
CNC Jog Speed Fast.png

3. Move Gantry To Job Home - Fine Tune

  • Set Turtle mode
  • Fine tune position until you get to the desired home position for X and Y
  • Setting Z home can be done automatically and discussed below
CNC Jog Speed Slow.png


4. Set new Home coordinates

  • Click SETUP (F1) -> PART Mode (F1)
CNC F1 Setup.png
CNC F1 Part.png

Set X Position

  • Press SET (F10) to set the X Home value to the current position.
  • Click NEXT AXIS (F1) to advance to Y
CNC Set X.png

Set Y Position

  • Click SET (F10) to set the Y Home to the current position
  • Click NEXT AXIS (F1) to advance to Z
CNC Set Y.png

Set Z Position

  • Click SET (F10) to set the Z Home to the current position
  • Click NEXT AXIS (F1) to return to X
CNC Set Z.png

5. Confirm Job Home

  • Press ESCAPE a few times to return to the main menu
  • Select MDI (F3)
  • Enter x0y0z0.25 in the Block and press ENTER to accept the command and then CYCLE START
  • The CNC will move the bit to the job home position with the bit setting at 1/4" above the surface of the material
  • You can use x0y0z0 if you want the bit to touch the material
  • Using the CNC Controls, press Z+ to move the bit away from the material
CNC F3 MDI.png
CNC Confirm Home A.png

SUCCESS

NEXT STEP

Click here for the next step

Retrieved from "https://wiki.makerfx.org/index.php?title=Forest_CNC_Set_Job_Home&oldid=3384"