Difference between revisions of "Forest CNC Set Job Home"
| Line 3: | Line 3: | ||
=== 1. Secure the material === | === 1. Secure the material === | ||
*Use clamps or whatever method is appropriate for your job | *Use clamps or whatever method is appropriate for your job | ||
| − | *You may have to use CNC Controls and manually move the gantry to allow room to secure your material | + | *You may have to use '''CNC Controls''' and manually move the gantry to allow room to secure your material |
=== 2. Move Gantry To Job Home === | === 2. Move Gantry To Job Home === | ||
| − | *Use CNC controls to move the gantry to the desired home position | + | *Use '''CNC controls''' to move the gantry to the desired home position |
| − | *To travel quickly to the other end of the table, enable Rabbit mode by clicking the Turtle / Rabbit button until the light is | + | *To travel quickly to the other end of the table, enable Rabbit mode by clicking the '''Turtle / Rabbit''' button until the light is '''OFF''' |
*Move gantry to approximate home position | *Move gantry to approximate home position | ||
| − | *Set Turtle mode | + | *Set '''Turtle mode''' |
*Fine tune position until you get to the desired home position for X and Y | *Fine tune position until you get to the desired home position for X and Y | ||
*Setting Z home can be done automatically and discussed below | *Setting Z home can be done automatically and discussed below | ||
=== 3. Set new Home coordinates === | === 3. Set new Home coordinates === | ||
| − | *Click SETUP (F1) -> PART Mode (F1) | + | *Click '''SETUP (F1)''' -> '''PART Mode (F1)''' |
| − | *Press SET (F10) to set the X Home value to the current position. | + | *Press '''SET (F10)''' to set the X Home value to the current position. |
| − | *Click NEXT AXIS (F1) to advance to Y | + | *Click '''NEXT AXIS (F1)''' to advance to Y |
| − | *Click SET (F10) to set the Y Home to the current position | + | *Click '''SET (F10)''' to set the Y Home to the current position |
| − | *Click NEXT AXIS (F1) to advance to Z | + | *Click '''NEXT AXIS (F1)''' to advance to Z |
| − | *Using the CNC Controls, move Gantry away from edge to create space for probe using the X,Y & Z move buttons | + | *Using the '''CNC Controls''', move Gantry away from edge to create space for probe using the X,Y & Z move buttons |
| − | *Click the AUTO (F4) button and CYCLE START | + | *Click the '''AUTO (F4)''' button and CYCLE START |
*Test probe by clicking button to assure button click registers | *Test probe by clicking button to assure button click registers | ||
*Put probe in place under the bit | *Put probe in place under the bit | ||
| − | *Click CYCLE START to initiate auto setting the Z home | + | *Click '''CYCLE START''' to initiate auto setting the Z home |
*The CNC will move the Z axis to set the new Z Home value | *The CNC will move the Z axis to set the new Z Home value | ||
| − | *DO NOT press SET (F10) at this point. The Z value has been automatically set. | + | *'''DO NOT''' press SET (F10) at this point. The Z value has been automatically set. |
| − | *Using the CNC Controls, press Z+ to move the bit away from the probe | + | *Using the '''CNC Controls''', press '''Z+''' to move the bit away from the probe |
*Remove probe and place it safely back on top of the controller | *Remove probe and place it safely back on top of the controller | ||
=== 4. Confirm Job Home === | === 4. Confirm Job Home === | ||
| − | *Press | + | *Press '''ESCAPE''' a few times to return to the main menu |
| − | *Select MDI (F3) | + | *Select '''MDI (F3)''' |
| − | *Enter x0y0z0.25 in the Block and press ENTER to accept the command and then CYCLE START | + | *Enter '''x0y0z0.25''' in the Block and press ENTER to accept the command and then CYCLE START |
*The CNC will move the bit to the job home position with the bit setting at 1/4" above the surface of the material | *The CNC will move the bit to the job home position with the bit setting at 1/4" above the surface of the material | ||
| − | *You can use x0y0z0 if you want the bit to touch the material | + | *You can use '''x0y0z0''' if you want the bit to touch the material |
| − | *Using the CNC Controls, press Z+ to move the bit away from the material | + | *Using the '''CNC Controls''', press '''Z+''' to move the bit away from the material |
=== SUCCESS === | === SUCCESS === | ||
*You have successfully set Job Home | *You have successfully set Job Home | ||
*Next step is to load and run your job | *Next step is to load and run your job | ||
Revision as of 18:05, 8 February 2021
Follow these steps to set the home position for your job. Think about how you have defined the job in VCarve Pro and set the home position to match that design.
Contents
1. Secure the material
- Use clamps or whatever method is appropriate for your job
- You may have to use CNC Controls and manually move the gantry to allow room to secure your material
2. Move Gantry To Job Home
- Use CNC controls to move the gantry to the desired home position
- To travel quickly to the other end of the table, enable Rabbit mode by clicking the Turtle / Rabbit button until the light is OFF
- Move gantry to approximate home position
- Set Turtle mode
- Fine tune position until you get to the desired home position for X and Y
- Setting Z home can be done automatically and discussed below
3. Set new Home coordinates
- Click SETUP (F1) -> PART Mode (F1)
- Press SET (F10) to set the X Home value to the current position.
- Click NEXT AXIS (F1) to advance to Y
- Click SET (F10) to set the Y Home to the current position
- Click NEXT AXIS (F1) to advance to Z
- Using the CNC Controls, move Gantry away from edge to create space for probe using the X,Y & Z move buttons
- Click the AUTO (F4) button and CYCLE START
- Test probe by clicking button to assure button click registers
- Put probe in place under the bit
- Click CYCLE START to initiate auto setting the Z home
- The CNC will move the Z axis to set the new Z Home value
- DO NOT press SET (F10) at this point. The Z value has been automatically set.
- Using the CNC Controls, press Z+ to move the bit away from the probe
- Remove probe and place it safely back on top of the controller
4. Confirm Job Home
- Press ESCAPE a few times to return to the main menu
- Select MDI (F3)
- Enter x0y0z0.25 in the Block and press ENTER to accept the command and then CYCLE START
- The CNC will move the bit to the job home position with the bit setting at 1/4" above the surface of the material
- You can use x0y0z0 if you want the bit to touch the material
- Using the CNC Controls, press Z+ to move the bit away from the material
SUCCESS
- You have successfully set Job Home
- Next step is to load and run your job
